Stationary Decoder

Decoders

Stationary Decoders

Throttles

Boosters

Power Management

Power Supplies

Wireless Controls

Computer Control

Detection & Signalling

Accessories

DS64 Quad Stationary Decoder

Price $ 73.95

The DS64 Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control. The DS64 hasn’t met a turnout it doesn’t like. From Solenoid turnout machines to slow motion motors, this affordable, easy to install decoder will add another dimension to your operations. Features Easy to install and operate. Operates four turnouts. Slow Motion Machines. Solenoid Machines Switch inputs for turnout control LocoNet Control Integral capacitor discharge. Operates from track power or a separate booster. Buffered switch inputs. DCC compatible.

DS44 Basic Quad Stationary Decoder
Price $45.95	DS44 NEED SOMETHING HERE!
	No frills stationary decoder. Simple installation and set up. Control 4 slow motion turnout machines from your DCC throttle. Quick set up for sequential addresses (like the DS54) Independent address set up also available (you can choose any stationary address for each turnout machine)

DS51K1 Stationary Decoder
Price $17.95	DS51K1 Stationary Decoder For Single Kato Unitrack Turnouts
	Easy to use Cost effective control for a single Kato Unitrack turnout or other similar device Rated at ½ amp. Great for HO & N Scale Small size .319” x .509” x .152” (8.11mm x 12.94mm x 3.88mm)

DS61K1 Stationary Decoder
Price $37.95	Convert Kato Manual Turnouts to Powered DCC Control! DS61K1L and R Stationary Decoder For Kato Unitrack Turnouts.
	Easy to use Cost effective control for a Kato* Unitrack turnouts HO Scale Easy 'bolt on' retrofit for Kato manual turnouts listed below DS61K1L Left Hand DCC Turnout Machine for Kato HO Unitrack $32.95 msrp DS61K1R Right Hand DCC Turnout Machine for Kato HO Unitrack $32.95 msrp These DCC Turnout machines convert Kato manual turnouts 2-840, 2-841, 2-862 and 2-863 to DCC powered turnouts (turnouts sold separately). *'Unitrack' is a Registered Trademark of KATO USA

DS52 Dual Stationary Decoder
Price $28.95	Features Simple hook up and set up. Control 2 individual turnout machines. 2 Slow motion turnout machines, such as Tortoise™ by Circuitron or Switchmaster™. OR 2 Solenoid type turnout machines such as three wire Peco or Atlas Snap Switches or two wire bi-polar type turnout machines such as Kato Unitrack, AristoCraft, or LGB turnouts with powerful capacitive discharge capability. Turnout addresses can be set individually or in groups of 2. Screw terminals make installation easy! DCC compatible.
	Screw terminals make installation and set up easy. Control 2 solenoid type turnout machines: 2 wire bi-polar (Kato Unitrack Switches, etc.) and/or 3 wire (Peco, Atlas Snap Switches, etc.) Addresses can be independent or sequential All Scales up to 22V track power.

DS54 Quad Stationary Decoder
Price $91.95	At first glance the sophistication of the DS54 may be a little intimidating. The DS54 is engineered to give you the basics of stationary decoder control as well as many advanced features that you might not have thought of yet. Never fear, you can use the DS54 as simply a turnout decoder. The factory programmed defaults make the DS54 usable "out of the box" in most systems without the need for any additional programming, configuration or wiring connections. You can use "just as much as you want" of the DS54's basic capabilities, & leave the more advanced features till you find that you need them for a specific task. The DS54 is a sophisticated input & output device for Digitrax Digital Command Control systems. It can control up to 4 turnout motors (either solenoid or slow motion type) or a combination of other types of stationary lights & devices. It also has 8 inputs, paired in 4 groups, that can trigger "local" DS54 output tasks & also broadcast several types of sensor & status information onto LocoNet, for action by command stations like the DCS100, or a PC connected to LocoNet. The DS54 has a powerful set of programmable actions that you can customize to generate local tasks without any intervention from Keypads/Throttles, Command Stations or attached computers. The ability of the DS54 to perform "autonomous" local tasks or "animation," gives the DS54 a greater synergy & capability than just a combination of a separate stationary decoder & sensor module. LocoNet gives you all this sophistication with less overall system complexity. In a large walkaround layout, DS54 inputs are easily configured to allow you to operate local turnouts (and routes) with momentary push-button switches on a local control panel fascia while still allowing remote users & computers to control these same turnouts. One really exciting example of the power of the DS54 is using just one of the DS54's four outputs you can set up a block occupancy detector with an associated flashing light output for a simple crossing gate detector & signals. In this case, the detection blocks are gapped to signal & "protect" several tracks at a grade crossing. Further, this "crossing gate" task running in 1/4th of the DS54, can also send block occupancy detector messages onto LocoNet for integrating into the Digitrax signaling control system. Since these sensor feedback messages are broadcast on the LocoNet network, they are also available for attached PC's showing CTC type displays.
	DS54 Features: 4 Multi-purpose high-current output control pairs controllable by standard DCC accessory decoder signals & local control inputs. Outputs can control: 1. Push-pull solenoid turnout motors e.g. PECO or Atlas "snap" switches 2. Slow Motion DC Stall turnout motors e.g. Switch Master & Tortoise type products 3. Incandescent & LED lights for signals & special effects 4. Other attached devices such as sound modules & DC motors 8 Multi-purpose sensor inputs can be configured for: 1. Block occupancy detectors, using Digitrax BD1 detector modules 2. Local turnout control 3. Feedback of turnout position, including "out of position" during changes 4. General LocoNet system input sensors 5. Local route control 6. System Power On/Off & Run/Stop inputs 7. Cascaded route & turnout control 8. Signaling system control messages 9. Local animation control, such as automated Indexing Turntable 10. Multiple aspect control such as automatic Crossing Gate controller 11. General local control of attached motors, solenoids, lamps, etc. § Approximate Size 2.5" x 4" x .75" § Includes wires for connecting 4 turnouts. § Fully programmable & customizable configurations § Configurations are permanently stored in non-volatile memory § Supports up to 4,000 individual LocoNet sensors on the system § Supports up to 2,000 turnout addresses including turnout feedback

DM-1 DC Motor Adapter
Price $11.95	The DM-1 is an inline adapter designed to modify any DS54 output to provide the bi-polar drive current needed to run reversible DC motors, solenoid switches (like Kato & LGB turnouts), lamps and other similar devices that draw up to 1/2 amp. Just plug the DM-1 into any DS54 output and the DM-1 socket will provide a bipolar drive rated at 500MA continuous and 1 amp surge.

RX4 4-ZoneTransponding Receiver Add-on for BDL Series Detectors
Price $56.95	4 ZoneTransponding Receiver Add-on for BDL16 series occupancy detectors. Use up to two RX4s with a BDL168 to add transponding to any 8 detection sections on your layout. Use one RX4 with a BDL162 or BDL16 to add transponding to any 4 detection sections on your layout. (Note: BDL16 & BDL162 are discontinued).

BDL162 Occupancy Detector

Price $142.95

Cost Effective LocoNet Advanced Occupancy Detection BDL16 LocoNet Universal Occupancy Detector for 16 detection sections. Complete LocoNet Occupancy detection (with NO DS54 required). Gives you local occupancy & zone power status reporting via fascia mounted LEDs &/or computer. Use BDL162 to enable operations mode read back for decoders equipped with this feature. $125.00 for 16 detection sections is less than $8 per detection section!